S-100-M1St2U Media Converter

3.1 in

4.7 in

1 in

Yes

1

1550 nm, 1310 nm

S-100-M1ST2U Transceiver/Media Converter, 100-240v AC, Regulated DC Adapter

100/140 µm, 62.5/125 µm, 50/125 µm, 85/125 µm

10.58 oz

Wall Mountable, Desktop, Rail-mountable, Rack-mountable

AC Adapter

1.24 Mile

S-100-M1ST2U Transceiver/Media Converter

Multi-mode

1

Twisted Pair, Optical Fiber

Yes

2

Transceiver/Media Converter

Fast Ethernet

10/100Base-T, 100Base-BX-U

u003c10-12

6 - 30 vDC, unregulated ( 12 vDC Nominal )

Pause should be enabled when all devices connected to the media ; converter support pause. Auto-Negotiation must be Enabled to use this ; feature; Enabled (Default)- ; The Media converter will advertise Pause capability during ; Auto-Negotiation on the 100Base-TX interface; Disabled- The Media ; converter will advertise that it does not have Pause capability during ; Auto-Negotiation on the 100Base-TX interface.

5% to 90% non-condensing

Up to 3,048 meters (10,000 feet)

6.8

Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron; Single Mode: 9/125 micron (ITu-T 625)

FCC Part 15 Class B*, EN55022 Class B*

5% to 95% non-condensing

2.0 watts

The media converter can perform a loopback on the 100Base-X fiber ; interface; Disabled (Default - Up); Enabled- The ; 100Base-X receiver is looped to the 100Base-X transmitter. The ; 100Base-TX transmitter is taken off the interface.

minimum range of -25 C to 70 C (-13 F to 158 F)

This green LED is operational only when power is applied. The LED is on ; when the 100Base-FX link is on and flashes with a 50% duty cycle when ; data is received.

5.5mm x 9.5mm x 2.1mm barrel socket

167 mA

1.5kv

EN 60825-1:2007

120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches

RJ45 connector, 2 pair CAT 5, EIA/TIA 568A/B or better cable

Enabled (Default)- ; The media converter uses 802.3u Auto-negotiation on the 100Base-TX ; interface. It is set to advertise full duplex; Disabled- The media ; converter sets the 100Base-TX port to full duplex.

100-240v AC, regulated DC adapter included

This green LED is operational only when power is applied. The LED is on ; when the 100Base-TX link is on and flashes with a 50% duty cycle when ; data is received.

UL 60950-1

EN55024

If Auto-Negotiation (802.3u) is enabled, the media converter uses the HP ; Auto-MDIX method for the 100Base-TX interface. If Auto-Negotiation ; (802.3u) is disabled the Media converter will use the RX Energy method ; on the 100Base-TX interface to set the port MDI or MDIX whichever is ; appropriate; Enabled (Default)- ; Either a straight-through or crossover type cable can be used to connect ; the media converter to the device on the other end of the cable; Disabled- If the ; partner device on the other end of the cable does not have the Auto-MDIX ; feature a specific cable, either a straight-through or crossover will be ; required to ensure that the media convertor's transmitter and the ; partner devices transmitter are connected to the others receiver. The ; Media Convertor's 100Base-TX port is configured as MDI with this switch ; setting.

Enabled (Default)- ; When the state of the receiver is changed on the 100Base-TX interface it ; is reflected on the 100Base-FX fiber transmitter. When the state of the ; receiver on the 100Base-FX interface is changed it is reflected on the ; 100Base-TX transmitter; When a Far-End Fault Indication is received on the fiber interface the ; 100Base-TX transmitter is turned off. When the Far-End Fault Indication ; is cleared the transmitter is turned back on; Disabled- The ; 100Base-TX and the 100Base-FX fiber interface operate independently. ; Far-End Fault indication on the 100Base-FX fiber interface has no effect ; on the 100Base-TX interface.

This green LED is turned on when power is applied to the media ; converter. Otherwise it is off. The LED will blink when in Loopback test ; mode.

0 C to 50 C (32 F to 122 F)

Canada

1